Wolf · Capitol Hill and the rest of Denver
Range Repair
The appliance where a cooktop and an oven share one frame: ignition above, cavity heat below, and the metering a mile of elevation changes.
What people describe on the phone
- Burner clicks and clicks on a cold morning before it takes
- Cooktop lights straight away and the cavity under it stays cold
- Flame either roars or drops out, with no usable middle
- Panel throws a fault and the oven refuses to start at all
Lines covered by this repair
- Dual-fuel and all-gas ranges 30 · 36 · 48 in · Igniters, spark modules, thermal fuses, oven sensors, altitude orifices
What it costs
What the repair itself runs
Six bands cover nearly every Wolf cooking fault in a Denver kitchen — parts, and the labour to fit them. Each one is a range, because the same symptom can turn out to be an electrode or the board sitting behind it.
The service call
Diagnosis is $89: a single flat charge covering the drive out and the fault-finding, then deducted from whichever repair you decide to approve.
Once the readings are in you are given one firm number from inside whichever band the fault falls in, agreed with you before anything is dismantled further. Approve it and the service call comes off that number. Say no and the visit ends there.
Repair band Parts and labour
- Igniter or spark module
- $180–$460
- Burner valve or orifice service
- $260–$620
- Oven thermostat or sensor calibration
- $190–$440
- Convection fan or motor
- $290–$660
- Control board or touch panel
- $450–$860
- Door hinge, glass or seal
- $270–$710
These are ranges, not starting prices. What moves inside one is the part itself and how far the unit has to come out of its cabinetry. For scale, buying your way out of it instead — a comparable professional range, before installation and ventilation work — runs $7,890–$16,930, and that is the arithmetic worth doing before you decide either way.
Describe what it is doing and we will say which band it is likely to land in: (720) 807-8323.
In their words
Denver kitchens, after the van left
Cherry Creek, Washington Park, Highland and Capitol Hill.
5.0/ 51,224 reviews
Front burner clicked for a minute before catching, worse on cold mornings. The electrode was cracked and caked with old boil-over, and he changed the switch under the knob too. Two days to get an appointment is the only reason for four stars.
Ainsley R.Washington Park
Old walk-up, small kitchen, faint gas smell whenever the oven ran. He traced a weeping fitting at the regulator, tightened and leak-tested it, then went round every other joint before packing up.
Linus O.Poets Row
The range came with the condo and had never simmered properly at this altitude. He read the manifold pressure, fitted the orifices Denver actually needs, and a sauce now sits at a bare bubble.
Dwayne H.Cherry Creek
Range Repair questions
Asked about range repair
The cooktop lights but the oven stays cold. Is that two faults?
On a dual-fuel range the cooktop is gas and the oven is electric, so they fail on their own. A working cooktop proves the gas side is fine and narrows the diagnosis to the oven: igniter, thermal fuse, sensor or board.
Why does my burner tick over and over on cold mornings?
A cracked electrode, moisture in the burner ports, or a spark module losing its edge. Cold, dry Denver mornings make a marginal electrode fail first thing and behave by lunchtime, which is why it is worth describing when it happens.
Can a range be re-metered for this altitude after the fact?
Yes. Manifold pressure is read, altitude orifices are fitted and the air shutters are set. That is a single visit and it is the fix for tall yellow flames, sooted pans and a simmer that will not sit still.
Next step
book a range repair visit
Model on the door, what the panel says, what the burner or the fan is actually doing. That is enough to bring the right part on the first visit.
Phone 24/7 · on site 8 am to 8 pm, every day of the week
Book a slot onlineDiagnosis $89, deducted from an approved repair.